Posts

Introduction This document briefly explains all relevant configuration commands supported by Regado devices, including syntax, parameters and command examples. The document also contains a reference on how to interface with the devices using the MQTT protocol, e.g. reading device input values and controlling the device outputs. Created: 30/08/2021 Last modified: 19/01/2025 Version: 8 Created by: Lukas D'Angelo Valid for FW builds: 01/01/2025 - current Basic Commands help The help or ? command shows a list of all commands supported by the current HA-EA platform. ...

This document briefly describes how to set up a basic Home Assistant environment to contorl 5 heating zones using a HA-EA-S device. Created: 08/09/2021 Last modified: 26/05/2021 Version: 4 Created by: Lukas D'Angelo Overview The heating zones are defined: Living room Kitchen Bathroom Bedroom 1 Bedroom 2 Each zone has its own electrical valve (230V~) which controls the radiator(s) and has a temperature sensor for temperature feedback. Wiring Network The Home Assistant APPLIANCE (e.g. Raspberry Pi) runs Debian 11 Bullseye including the following software: ...

Introduction This document briefly explains all relevant configuration commands supported by HA-EA devices, including syntax, parameters and command examples. Created: 30/08/2021 Last modified: 26/05/2022 Version: 6 Created by: Lukas D'Angelo Note: This reference is valid for FW-builds as of 05/2022. Basic Commands help The help or ? command shows a list of all commands supported by the current HA-EA platform. Syntax help Parameters None Example $ help clear Clears the Terminal Screen defaults Load default Configuration diagmode Diagnostic Mode Configuration Commands fwupdate Update the System Firmware hostname Set Hostname of the System hw Hardware Platform Configuration Commands ip Internet Protocol Configuration Commands mqtt MQTT Protocol Configuration Commands password Set Management Password of the System restart Restart the System now save Save running Configuration to Flash show Show System Parameters telnet Telnet Management Configuration Commands username Set Management User of the System wifi WiFi Interface Configuration Commands Note: ? is also used to give hints about the syntax or options of a command. ...

Overview Internet Connectivity: KONVERTO FTTH 150Mbps↓/90Mbps↑, 1 satic IPv4 address, 1 static IPv6 /56 network Router: Huawei AR169-FVW Switches: Edgecore ECS4210-12T (LKS_GLURNS_SW1), Cisco 2960G-8TC-L (LKS_GLURNS_SW2) WiFi APs: 2 x Zyxel NAP102, 2 x Zyxel NWA1123-ACV3 (cloud managed) Server: Supermicro X10SLM, Intel Xeon E3-1230 v3 CPU, 32GB ECC RAM, 2x1TB Samsung 870 QVO in RAID1, 2x4TB Seagate ST4000VN008 in RAID1, 4TB WD HDD for backup files The network spans over 2 houses and covers 4 flats in total to share one internet link. ...

This document briefly describes all relevant features and shows the hardware specs of current HA-EA models. HA-EA is a range of devices that provide I/O to control devices and systems (e.g. heating and irrigation plants, lighting, domotics) and gather environmental data over an IP-based network. Created: 16/07/2020 Last modified: 11/10/2021 Version: 4 Created by: Lukas D'Angelo Model & feature overview Model Ethernet interface WiFi interface Relay outputs Digital inputs Sensor BUS Extension module HA-EA-S none 802.11b/g/n 8 0 1-Wire HA-EA-S-EXT HA-EA-ETH 10/100BASE-T 802.11b/g/n 8 0 none HA-EA-S-EXT HA-EA-I16 10/100BASE-T 802.11b/g/n 0 16 x 230V~ 1-Wire none HA-EA-TL none 802.11b/g/n 0 0 1-Wire yes HA-EA-R none 802.11b/g/n 2 2 x 230V~ 1-Wire none Ethernet interface A WIZnet W5500 IC provides ethernet connectivity. Auto negotiation is enabled by default, PHY-speed and DUPLEX-capability are gathered automatically. The TCP/IP stack is offloaded to the W5500 IC in order to reduce the load on the microcontroller when ethernet is used. ...